DreamBox DM7020
Linux Digital Satellite Receiver
Feature
50 MHz PowerPC processor
Puzzle, the Linux operating system
Large-size LCD display
MPEG-2 hardware decoding, DVB- S
1 x DVB Common-Interface Slot
2 x Smart Card Reader (Dreamcrypt CA)
V.24 / RS232 interface
Integrated Compact Flash slot
10/100 Mbit Ethernet interface compatible
Analog modem
1 x USB
Interface for digital bit S / PDIF stream out (AC-3)
2 x Scart- Interface
RF modulator
With audio / video cinch
32 MB flash and 96 MB RAM
Embedded IDE interface
Support for any potential internal IDE HDD 3,5 “
TV / radio unlimited channel lists for
Channel change time <January 2
Automatic scanning service
Immediately bouquet list
EPG (Electronic Program Guide)
Videotext Decoder
Many LNB- Switching control (DiSEqC)
OSD in many languages and skin support
DreamBox DM7020 technical data
DBS-Tuner:
950. 2150 MHz frequency range
Signal Level – 65 dBm is. – 25 dBm
12 dB signal-to-noise level Max.
DBS-Tuner Input Connector F-Type Female
75 ohm input impedance
AFC +/- 3 MHz
Size QPSK demodulation
Viterbo FEC and Reed-Solomon
Viterbirate 02/01, 03/02, 04/03, 06/05, 08/07
Skruhlenyya ratio 35%
The ISO 13,818 to 1 Demultypleksyrovanye
Common interface:
Common-Interface Power Max. 0,3A / 5V
Video decoder:
Video Compression MPEG-2 and MPEG-1 compatible
Video Standard PAL G / 25 Hz
Video Formats 4: 16.3: 9
4 letterbox: 3 TV devices
Audio decoder:
Audiokompression MPEG-1 and MT; MPEG-2 Layer I and II
Dual sound mode (master / slave), stereo
Frequency: 32 kHz, 44.1 khz, 48 khz, 16 kHz, 22.05 kHz, 24 kHz
Analog output:
600 ohm output level L / R 0.5 VSS
THD> 60 dB (1 kHz)
Crosstalk <-65 dB
Digital output:
75 ohm output level of 0.5 VSS
Selective Filtering data 32 kHz, 44.1 khz, 48 khz
S / PDIF optical out (AC3)
Video options:
In the VSS 0.3 dB +/- 75 ohms Input Level FBAS
ETS 300 472 according to the standard teletext filter>
TV-Scart:
Output: Over selected OSD FBAS, RGB, S-Video
Visiar- Scart:
FBAS
Serielle RS-232 interface
Bidirectional RS232 type
115.2 kbit / s Max flow.
Connector SUB-D-9
Function: Firmware Update
Ethernet:
10/100 Mbit compatible interface
Firmware Update Function
USB:
USB 1.2 Connector
Mini DIN:
The steering control I2C peripherals
IR Funktion
Pins:
A 5V
Two SDA (i2c- Canal 2)
3 SCL
4 3,3V
7 GND
8 IR output
9 GND
UDMA66 IDE interface:
Connect the HDD intern
Compact Flash – Reader
LNB power and polarization:
LNB Current 500mA max. ; Protected against short circuit protection
Supply at 400mA LNB Voltage vertical <without load 14V,> 11,5V
Supply 400mA LNB Voltage horizontal <without load 20V,> 17,3V
LNB off in standby mode
Count of active satellite position:
DiSEqC 1.0 / 1.1 / 1.2 and USALS (Rotor Control)
Power consumption:
<20W (in operation, horizontal polarization / 400mA LNB current)
<15W (in operation, LNB without)
<10W (deep-sleep mode)
Input voltage:
230 V / 50 Hz AC +/- 15%
Physical characteristics:
Ambient temperature of 15 ° C … + 35 ° C
Humidity <80%
Dimensions (W x D x H): 374 mm x 230 mm x 75 mm
Weight: HDD 1.8 kg without
Downloade DreamBox DM7020 Firmware 12-09-205
Download User Manual English
____________________________
Universal DreamUP Version 1.3.3.11
________________________________
RMA Onloine Service
Dream Verification
Download
Flash Dream box with compect Flash
Download
________________________________
How To Upgeade Dream Box
Update Flash With Loader (Dreamup)
Power off Your box and open Loader
Select port com and select Networ or no Networ
If select Network then put IP of your PC and Box ip from yor Remot
First Press Connect Button from loader and power on your box
When Loader Connect with stb Press Flash button
Select Firmware You want to Upgrade and press open
Now Flash Upgrading will be Start and wait..
Ofter Flash Done Press ok and Disconnect the box from Loader and Exit.Restart Box and Enjoy with new Flash
Flashing DreabBox All Models with Browser Just Click
Requirments
Image File Youwant To Upgrade in *nif Extension
DHCP Server, configured boot loader, Serial Cable, terminal program
like Hyper Term.
Browser Network Cable< Cros Cable if you want to Coneect Box Directly With PC.
For More Protection Use Second Stage Loader its Not Broken and Present
If You Don,t Have a DHCP Server Then Put IP in Loader Serial Port Setup
Shut Down The Dream Box From Power Switch or Deep Stand By Mode
1-Press and Hold the Front Panel Lower Button
2-Still Hold the Button and power on your Box
3-“*** STOP ***” These Text appear,if other text appear like “/flash”.. this Then you press and hold wrong lower Button.Now Leave the Lower button you hold.The boot loader will gon in Waiting Mode.
4-Above the “*** STOP ***” text, there must be an IP address (four decimal values with a dot in between) appear. If there appears the string “dhcp” instead, the box still looking for a DHCP server. A little wait. If it does not change, does not do anything with the DHCP server. Make sure the network cable is connected, etc.
if it is not workin then set ip Usin Serial Terminal
Open Browser in your PC
1-In Address line enter “http://ip/” where ip must be replaced with the value in the LCD
2-Press Firmware Upgrade Button in the Bottom of page
Now Select Image file you want to Upgrad Only in .nfi Extension Not in img etc
Click the flash button and wait it maybe
Restart your box and new Image willbe apear
take
How to make manual ip in Loader Dreambox All Models(Just Click)
If You don,t have a DHCP Server, configured or Ruter No Problem and don,t Instal one.Only you need to connect a serial terminal now
That’s why you need the IP address of your Dreambox gives. Your IP I, asksomeone help please, do not know what to choose. Your computer, your “next” IP address, you can choose any IP address but can not be used by another device theIP is. Another device is used as an example, your computer’s IP address is 192.168.0.5, and you, use192.168.0.10 said. In this case, only 192.168.0.11. Or whatever. This is the only x> = 1 and <= range 192.168.0.x, I, where 254,.
Hyperterm For example, start your favorite terminal program. Com port 115200 / 8N1 set. “S” Press.
Now you should see the setup menu. It should look like the following screenshot
Press the right arrow. You are now in the network setup menu.
Using “+” or “-” you can use the “Network Type” to see the series “Manual”.
Now you can enter an IP address below. Press F9 to save your settings.
Dreambox close.
Now go back and the procedure again. “DHCP” may not be displayed, instead of the IP you entered
